Chiller Fan Speed Too Low / Too High (CT 1.5 Install Dx)

Required Tools

• Phillips Screwdriver (#2)

Before Continuing

During the Install Diagnostics test, the filter should not be installed, and water and CO2 should not yet be turned on. If these steps have already been done:

• Turn off water supply
• Turn off the CO2 tank by rotating the handle clockwise until it stops.

Troubleshooting

Task 1: Repeat the Diagnostic Test

1. Verify water and CO2 are turned off, and filter is NOT installed.
2. Restart the diagnostic tests to see if it passes on the second attempt.
3. If the test continues to fail, power cycle the Bevi via the power switch on the front of the chiller.
   • Navigate back through the installation steps to the Install Diagnostic step and repeat the test.
   • If the test continues to fail, continue to Task 2.

Task 2: Power Off the Bevi.

1. Power off the Bevi using the power switch on the front of the chiller.
2. Disconnect the power cord from the back of the chiller.

Task 3: Remove the chiller from the cabinet.

1. Carefully lift the front of the chiller so the locating tabs on the bottom can come up and out of the ventilation holes.
2. Slide the chiller forward so the front hangs over the edge of the cabinet.

3. Remove the red locking clip and disconnect the 3/8" water supply line from the back of the chiller.
   • This step may not be necessary if there is enough slack on the water line to fully remove the chiller without putting tension on the tubing.

4. Lifting from the front and the rear grab handle, carefully lift the chiller out of the cabinet and place on the floor.

Task 4: Remove the left side panel.

1. Using a #2 Phillips screwdriver, loosen the two screws securing the top panel of the chiller.
2. With the screws fully loosened, lift the front of the panel up, and slide forward to release the rear locating tabs.
3. Place the panel to the side.

Task 5: Remove the PCB panel.

1. Using a #2 Phillips screwdriver, loosen the screw securing the PCB panel on the left side of the chiller.
2. With the screws fully loosened, lift the panel to release the lower locating tab and remove.
3. Place the panel to the side.

Task 6: Inspect the Chiller Fan Connection.

1. Locate the Chiller Fan connection on the BUC Board.
2. The fan cable cable has one blue, and one orange wire.
3. Inspect the Fan cable.
   • Confirm that the cable is connected and fully seated.
   • Inspect the wires and connector for any visible damage or loose pins.
     • If there is any damage to the cable or connector, please contact Bevi Support at 866-704-2384.

4. Gently disconnect, and reconnect the Fan cable.
   • There is a lock latch on the connector that needs to be depressed to disconnect the cable.
   • When reconnecting, ensure the connector is fully seated and clicks into place.

5. There are also two wiring connections at the bottom of the Chiller Fan, but these are not accessible when the chiller is fully assembled.
   • Visually inspect to see if they appear to be connected.

Task 7: Reinstall the Chiller.

1. Reinstall the PCB panel.
   • Take care not to pinch any wiring in the panels.
   • Ensure the locating tabs slot into place.
   • Tighten the screw to secure the panel.
2. Reconnect the chiller power cord.
3. Carefully lift the chiller into place in the cabinet.
   • Ensure the locating tabs on the bottom of the chiller fit into the ventilation holes and the chiller sits flush on the base of the cabinet.
4. If it was disconnected during removal, reconnect the 3/8" water supply tube.
   • Ensure the tubing is fully seated into the push to connect fitting.
   • Reinstall the red locking clip.
5. Power on the chiller.

Task 8: Repeat the Diagnostic Test

1. Once the Bevi starts up, continue through the Install Wizard back to the diagnostics step.
2. Rerun the test.
   • If the test passes, continue with Installation.
   • If the test continues to fail, please contact Bevi Support at 866-704-2384 (BEVI).