[Guide] Bevi Standup 2.0 Removal and Replacement Guide - Manifold 1

Overview

This guide provides a step-by-step process for removing and replacing the Manifold 1 in a Signature Standup (SU 2.0) machine.

In this article (click to jump):

• Required Tools & Materials
• Remove and Replace Procedure
  • Task 1: Open the door and navigate to the Troubleshooting Tools menu.
  • Task 2: Depressurize the water system
  • Task 3: Remove Manifold 1
  • Task 4: Reinstall Manifold 1
  • Task 5: Test Functionality

Required Tools & Materials

• Manifold 1 Assembly (FRU P/N 720-0058)
• #2 Phillips Screwdriver
• #3 Phillips Screwdriver
• Flush cut pliers
• Zip ties

Remove and Replace Procedure

Task 1: Open the door and navigate to the Troubleshooting Tools menu.

1. Navigate to the Service Panel.
   1. Touch the gear (service) icon on the main dispense screen.
   2. Touch "Start Service" on the right side of the screen.
   3. Enter the access PIN “1986”.
2. The door should open. If it doesn't, press the “Open Door” button.
   1. If the door does not open, please contact Bevi Support at 866-704-BEVI.

3. From the service panel, touch "Alerts and Maintenance", then "Troubleshooting Tools"

Task 2: Depressurize the water system

1. Turn off the water source to the machine by closing the valve on the Bevi supply line.

2. Close the Buffer Tank.
   1. With the door open, access the buffer tank valve through the access hole above the filter.
   2. Turn the valve clockwise to close the Buffer Tank.
      1. The valve should be pointed forwards out of the access hole when in the closed position.

3. From the Troubleshooting Tools menu, dispense cold water.
   1. Place a small bucket or container under the dispense nozzle.
   2. In the lower left corner of the screen, press and hold “Pour” for cold water until no water is dispensing.

Task 3: Remove Manifold 1

1. Remove the center portion of the Bevi back panel.
   1. Loosen the 4 screws securing the panel (you do not need to fully remove them).
   2. Remove the panel by lifting up and unhooking panel tabs from the mounting screws.

2. Disconnect the water supply line from the Bevi by releasing the push to connect fitting.

3. Remove the metal bracket holding the water inlet fitting by removing the 4 Phillips head screws.
   1. Manifold 1 is directly behind this bracket.

4. Disconnect the Water Pressure Sensor Connector.
   1. Disconnect the wired connector, being careful not to pull directly on the wires.
   2. Use the spring latch to disconnect.

5. Cut zip ties holding the tubing to the bracket.

6. Disconnect all 4 tubes from the manifold.
   1. Manifold connections are labeled.
   2. Remove the red locking clips, and disconnect tubes.

7. Clip the zip ties holding the Manifold 1 wiring to the buffer tank bracket.
   1. Cutting these cable ties allows you more slack to access the back side of Manifold 1.

8. Remove the two mounting screws for the Manifold 1 w/ bracket, located on the backside of the bracket at the base.
   1. These can be removed with a #3 Phillips screwdriver, or a 3/8" socket with extension.

9. Disconnect the Inlet Solenoid and Ice Bank Solenoid wiring.

Task 4: Reinstall Manifold 1

1. Reconnect Inlet Solenoid and Ice Bank Fill solenoid wires.
   1. Red/Grey for Inlet valve.
   2. Red/Blue for Ice Bank Fill valve.

2. Reinstall manifold & bracket into machine using the two phillips screws previously removed.

3. Connect water tubing to the new manifold.
   1. Ensure tubing is fully seated into push-to-connect fittings.
   2. Reinstall the red locking clips.

4. Secure all 4 tubes to the bracket with new zip ties.

5. Reconnect water pressure sensor connector.
   1. Ensure the connector is fully inserted and clicks into place.

6. Install inlet bracket and reconnect water source to inlet valve.

7. Turn on the water source and reopen the Buffer Tank Valve.

Task 5: Test Functionality

1. Check all connections and inspect for leaks.
   1. From the service panel, Troubleshooting Tools, Controls menu, open the inlet solenoid and check internal water pressure.

2. If there are any leaking fittings, check to ensure all tubes are fully inserted into push to connect fittings.
3. All tubing should have factory marking indicating proper depth for insertion.

2. Test functionality of the machine to ensure correct installation and operation.
3. If the machine is functioning properly, reinstall the back panel.

If you have any questions or need further assistance, please contact Bevi Technical Services at support@bevi.co, or call our support line at 866-704-2384 (BEVI)